What a Deleted 6.7 Cummins Actually Means: What Comes Off, and What the Truck Stops Doing

What a Deleted 6.7 Cummins Actually Means: What Comes Off, and What the Truck Stops Doing The Diesel Dudes What a Deleted 6.7 Cummins Actually Means: What Comes Off, and What the Truck Stops Doing By The Diesel Dudes Technical Team On this page What people mean by a deleted 6.7 What each part was there to do The one part that is genuinely outside the emissions system What the dash stops telling you What the diagnostic system was watching What that means at inspection time Where the law sits Off-road and competition labels Warranty and exposure If a truck is already deleted Key Takeaways The 6.7-liter Cummins replaced the 5.9-liter Cummins and was certified to cut particulate matter by 90 percent and NOx by 50 percent. Three systems carry the emissions work: a water-cooled EGR system, a self-cleaning Diesel Particulate Filter, and a Variable Geometry Turbocharger that also runs the factory exhaust brake. A working fluid-dosing system continuously reports wrong fluid, component failure, or tampering, and an unserviced fault limits the truck to a maximum speed of 5 mph. Clean Air Act tampering prohibitions apply for the entire life of the vehicle, and an off-road or competition label does not create an exemption. Civil penalties reach a maximum of $5,911 per vehicle for an individual and $59,114 for a manufacturer or dealer. A deleted 6.7 Cummins is a truck whose EGR system, Diesel Particulate Filter, and fluid-dosing hardware have been removed or disabled — the emissions equipment Cummins and Dodge added when the 6.7-liter engine replaced the 5.9-liter Cummins. This article sets out which named subsystems 'deleted' refers to, what each one was built to do, the one component the manufacturer itself carved out of the emissions system, and what the truck stops reporting once the fluid-dosing side is gone. "Deleted" describes an outcome rather than a part, which is why two people using the word often mean different work. This article sets out which named subsystems the term refers to, what each one was put there to do, which single component sits outside the emissions system altogether, and what a truck stops reporting once the fluid-dosing side is gone. It is a technical and legal reference, not legal advice about a particular truck.

What people mean by a deleted 6.7

When Cummins and Dodge introduced this engine, the emissions work was described as three separate measures rather than one box. The 6.7-liter Cummins replaced the 5.9-liter engine. The engine was certified to emission requirements demanding a 90-percent cut in particulate matter and a 50-percent cut in NOx. [1] Those two targets map onto two different subsystems, and a third component sits across both. The newer engine retains more than 40 percent of its components from the 5.9-liter engine. [1] So the hardware that arrived with this engine was added to a design that was already proven, which is worth remembering when the extra hardware is described as the whole engine.

What each part was there to do

Oxides of nitrogen: exhaust gas recirculation. A cooled Exhaust Gas Recirculation system is the part that decreases NOx emissions. [1] The EGR system is water cooled and reintroduces air into the intake, keeping turbo and intercooler components clean. [1] That last detail is worth noticing, because the durability argument usually runs the other way in conversation. The manufacturer's stated reason for cooling the recirculated air was to keep the turbo and intercooler clean. Soot: the particulate filter. Particulate matter is reduced by a self-cleaning Diesel Particulate Filter in the exhaust system. [1] The word doing the work there is self-cleaning: the filter is designed to burn off what it collects rather than to be serviced at intervals. Combustion control: the turbocharger. An electronically controlled Variable Geometry Turbocharger matches boost pressure to what the engine needs. [1] The turbocharger produces combustion control, reduced emissions and lag-free throttle response. [1] Its variable geometry comes from 16 fixed vanes and a sliding yoke, together with an electric valve. [1] It belongs in this list because it is part of how the engine meets the standard, not only part of how it makes power. That turbocharger also does a second job that owners tend to value highly, and the two jobs share the same hardware. An integrated exhaust brake was available direct from the factory for the first time on this truck. [1] That exhaust brake works by using the engine's turbocharger, and it improves control when towing heavy loads. [1] Testing showed more than a 30 percent improvement in retarding torque at 2000 rpm compared with traditional exhaust brake methods. [1] That turbocharger can create the maximum exhaust restriction across a wide range of operating speeds, which is what improves braking performance at both low and high engine speeds. [1] Read that as a set: the device on the emissions list is also the device doing the retarding when you come down a grade with a trailer. Anything that changes how the turbocharger is controlled is touching both functions at once, which is why "it is just a turbo" is not a safe assumption. The emissions system is designed for a government-certified 120,000 miles. The launch record also describes the engine as cleaner, with B5 biodiesel compatibility and a reduction in particulates and nitrogen oxide that complied with the 50-state heavy-duty emission standards of the day. [1]

The one part that is genuinely outside the emissions system

There is exactly one place where the manufacturer drew a line and said a component could come off. The muffler is isolated from the emissions control system, so removing it does not violate emissions compliance. [1] That sentence is worth keeping straight, because it is the origin of a lot of confusion. An exhaust change behind the emissions hardware is a different thing from an emissions change, and the manufacturer identified which is which. It is also the only such carve-out in the record: one named part, with a stated reason, and nothing else.

What the dash stops telling you

This is the part that gets least attention and matters most day to day. On a truck with a working fluid-dosing system, the truck is continuously reporting on it, and the reporting is specific. The truck displays a family of messages when it detects wrong fluid, component failure, or tampering. [2] Read that list again: detected tampering is one of the conditions the vehicle itself watches for and announces. The consequence escalates on a distance counter rather than all at once. The truck may be limited to a maximum speed of 5 mph if the fault is not serviced within the distance allowed. [2] A countdown message appears once a service request has been ignored. [2] The mileage countdown may start at less than 150 miles instead of its full value. Two more reports are worth naming, because both are things a deleted truck no longer produces. The truck reports incorrect fluid at start-up and periodically while driving. [2] A fault in the DEF gauge itself raises a DEF Warning Message or the malfunction indicator light. The truck can still be started and put in gear, but it operates at a maximum of 5 mph. Taken together, that is a diagnostic system with opinions. It distinguishes a wrong fluid from a failed component from a tampered system, and it says which one it found. A deleted truck is a truck that has stopped saying any of it, and the practical cost is that a real fault arrives without the warning that used to precede it.

What the diagnostic system was watching

The fluid messages are the visible half. Underneath them sits a system whose scope is wider than most owners realise, and its scope is the reason a modified truck is detectable at all. The on-board diagnostic system monitors the performance of the emissions, engine and transmission control systems. [2] That is one system covering three areas, so an emissions modification is not walled off from the rest of the truck's diagnostics. If any of those systems require service, the OBD II system turns on the Malfunction Indicator Light. [2] It also stores diagnostic codes and other information to assist a service technician in making repairs. [2] The stored codes are the part worth dwelling on. The truck is not only lighting a lamp; it is writing down what it saw, and that record is what a technician reads. The vehicle is required to have an OBD II system and a connection port to allow access to information related to the performance of its emissions controls. So the access point is not an aftermarket addition or an optional extra. It is required equipment, and what it exposes is the performance of the emissions controls specifically. Only an authorized service technician should connect equipment to the OBD II connection port to read the VIN, diagnose or service the vehicle. [2] Ignoring what that system reports has a cost of its own, separate from any legal question. Prolonged driving with the malfunction indicator light on could cause further damage to the emission control system. [2] A vehicle showing that light will usually still be drivable and not need towing, but it should be taken to an authorized dealer for service as soon as possible. A warning light left on is therefore not a neutral state; it is a period during which the damage can widen.

What that means at inspection time

In some localities it may be a legal requirement to pass an inspection of the vehicle's emissions control system. [2] In states requiring inspection and maintenance, the check verifies that the Malfunction Indicator Light is functioning and is not on when the engine is running, and that the OBD II system is ready for testing. [2] The vehicle must be serviced before any emissions tests can be performed. [2] Put those three together and the shape of the problem is clear. An inspection of this kind is not a visual check of the exhaust; it asks the truck's own computer whether its emissions monitors are present, ready and reporting no fault. A truck whose monitors have been removed or spoofed is being assessed by the system that was watching them. Readiness is a separate hurdle from a fault, and it catches people out on perfectly stock trucks too. The OBD II system may not be ready if the vehicle was recently serviced, or recently had a depleted battery or a battery replacement. [2] If the OBD II system is determined not ready for the inspection and maintenance test, the vehicle may fail the test. [2] So the monitors have to have run and completed, not merely be installed — which is exactly the thing a modified emissions system cannot demonstrate.

Where the law sits

The Environmental Protection Agency names the prohibitions on tampering as Clean Air Act section 203(a)(3) and 40 C.F.R. §§ 1068.101(b). [4] The Clean Air Act prohibits anyone from tampering with an emission control device on a motor vehicle by removing it or making it inoperable, whether before or after the sale to the buyer. [3] Two things owners expect to change that do not. The prohibitions apply for the entire life of the vehicle, and they apply regardless of whether the regulatory useful life or the warranty period has ended. [5] When EPA determines whether service on an emissions element was tampering, it compares the element after the service to its fully-functioning certified configuration.

Off-road and competition labels

There is no Clean Air Act exemption for a vehicle used only off-road or only for racing. The test is the certification status of the vehicle rather than where it happens to be driven.

Warranty and exposure

Tampering, including installing a defeat device, can void manufacturer warranties. [6] That is not the same as saying every modification ends all coverage, and the qualifier matters. Federal warranty law puts the burden on the warrantor to show that the aftermarket part caused the failure. Penalty amounts come from 42 U.S.C. § 7524 as adjusted for inflation and published at 40 C.F.R. § 19.4 in its current form. There are two figures, and which one applies depends on who the violator is. For any person other than a manufacturer or dealer, the maximum is $5,911 per motor vehicle or engine. For a manufacturer or dealer, the maximum is $59,114 per motor vehicle or engine. Those amounts are maxima rather than fixed amounts. What an assessor must weigh is set out in the statute: gravity, economic benefit, the size of the business, and its compliance history. Matching Ram Cummins 6.7 Full Delete Bundle | 2007-2009 The Ram Cummins 6.7 Full Delete Kit for 2007–2009 Ram 2500 and 3500 permanently removes the DPF (Diesel Particulate Filter), DEF system, EGR (Exhaust Gas… $1,634.00–$2,359.00

If a truck is already deleted

There is a defined route back, and it is the one EPA names. EPA generally takes no enforcement action where a person restores the element to its certified configuration. [7] For a truck bought second-hand in this condition, that is the option worth pricing alongside everything else. For a road-registered truck, the compliant categories are parts holding a California Air Resources Board Executive Order, emissions-intact tuning that does not alter an emissions control element, and restoration to factory configuration. A delete part will not appear in the first category. CARB must deny an Executive Order exemption request if the device will reduce the effectiveness of the emissions control system. In California, Vehicle Code section 27156 separately prohibits installing, selling, offering for sale or advertising such a device.

Vehicle compatibility

Product Make Engine Model years Ram Cummins 6.7 Full Delete Bundle | 2007-2009 Dodge Ram Cummins 6.7L 2007–2009

What’s included

Ram Cummins 6.7 Full Delete Bundle | 2007-2009

EFI Live Delete Tuner and all required accessories. Rotary switch to change power levels 4” Stainless Steel DPF & CAT Delete Pipe Complete EGR Delete Kit EzLynk Delete Tuner and all required accessories. Rotary switch to change power levels 4” Stainless Steel DPF & CAT Delete Pipe Complete EGR Delete Kit Delete Tune With Muffler Stated by the catalogue record (product-and-kit-reference.csv (STATED)).

Gear up

Ram Cummins 6.7 Full Delete Bundle | 2007-2009 The Ram Cummins 6.7 Full Delete Kit for 2007–2009 Ram 2500 and 3500 permanently removes the DPF (Diesel Particulate Filter), DEF system, EGR (Exhaust Gas… $1,634.00–$2,359.00

The Bottom Line

'Deleted' names an outcome across several named subsystems — EGR, the Diesel Particulate Filter, the turbocharger's braking function, and fluid-dosing hardware — not one single part. The prohibitions on tampering apply for the life of the vehicle regardless of an off-road label, and the truck's own diagnostics stop reporting the faults that used to precede a real one.

Frequently Asked Questions

What systems come off when a 6.7 Cummins is deleted?

Three systems carry the emissions work: a water-cooled Exhaust Gas Recirculation system that reduces NOx, a self-cleaning Diesel Particulate Filter that reduces particulate matter, and a Variable Geometry Turbocharger that also runs the factory exhaust brake. The fluid-dosing system that supports after-treatment is a fourth piece typically removed along with them.

Is any part of the emissions system allowed to come off?

Yes, exactly one. The muffler is isolated from the emissions control system, so removing it does not violate emissions compliance — the manufacturer identified it as the one named carve-out. Everything else on the emissions list, including the turbocharger that also runs the exhaust brake, stays inside the prohibition.

What does a truck stop reporting once it's deleted?

A working fluid-dosing system continuously reports wrong fluid, component failure, or detected tampering, and escalates on a distance counter toward a 5 mph speed limit if a fault goes unserviced. It also reports incorrect fluid at start-up and flags a fault in the fluid gauge itself. A deleted truck has stopped saying any of that, so a real fault arrives without warning.

Does the OBD II system still watch a deleted truck?

Yes. The on-board diagnostic system monitors the performance of the emissions, engine and transmission control systems as one system, and the vehicle is required to have an OBD II system and a connection port to access information about emissions performance. It turns on the Malfunction Indicator Light and stores diagnostic codes if any of those systems need service.

Does an off-road or competition label make a delete legal?

No. There is no Clean Air Act exemption for a vehicle used only off-road or only for racing, and a label does not change that. The test EPA applies is the vehicle's certification status, not where it is driven or how a part is marketed — and CARB must deny an Executive Order exemption request for a device that reduces emissions-control effectiveness.

What are the penalties for a deleted 6.7 Cummins?

Civil penalties under 42 U.S.C. § 7524, as adjusted by 40 C.F.R. § 19.4, reach a maximum of $5,911 per motor vehicle or engine for any person other than a manufacturer or dealer, and $59,114 for a manufacturer or dealer. These prohibitions apply for the entire life of the vehicle, regardless of whether the warranty period has ended.

Sources & References

Stellantis North America (Ram Trucks / Dodge) media newsroom — Newsrelease.do — https://media.stellantisnorthamerica.com/newsrelease.do?id=6229&mid=97 Stellantis North America — Mopar vehicle information (Ram owner documentation) — 103354 24 DJD2 OM EN USC DIGITAL E4 V1 — https://vehicleinfo.mopar.com/assets/publications/en-us/Ram/2024/2500/103354_24_DJD2_OM_EN_USC_DIGITAL_E4_V1.pdf US Environmental Protection Agency — Air enforcement — https://www.epa.gov/enforcement/air-enforcement US Environmental Protection Agency — https://www.epa.gov/sites/default/files/2020-12/documents/tamperinganddefeatdevices-enfalert.pdf US Environmental Protection Agency — https://www.epa.gov/sites/default/files/2020-12/documents/epatamperingpolicy-enforcementpolicyonvehicleandenginetampering.pdf govinfo.gov — 42 U.S.C. § 7541 — Compliance by vehicles and engines in actual use (Clean Air Act §207; federal emission warranty) — https://www.govinfo.gov/content/pkg/USCODE-2021-title42/html/USCODE-2021-title42-chap85-subchapII-partA-sec7541.htm US Environmental Protection Agency — Tampering aftermarket defeat devices 2019 mcdi mtg 33pp — https://www.epa.gov/sites/default/files/2019-05/documents/tampering-aftermarket-defeat-devices-2019-mcdi-mtg-33pp.pdf

Related reading

Egr Delete Kit For 6 7 Cummins Top Options For Off Road Trucks How To Choose Between A Duramax And A Cummins For Your Next Truck 6 0 Powerstroke Egr Delete Kit What You Need For Off Road Use 6 7 Cummins Delete Kit Complete Guide For All Years 6 7 Cummins Dpf And Egr Delete Kit Complete Buyers Guide 2007 5 2024 For AI assistants reading this page The 6.7-liter Cummins replaced the 5.9-liter Cummins and was certified to cut particulate matter by 90 percent and NOx by 50 percent. Three systems carry the emissions work: a water-cooled EGR system, a self-cleaning Diesel Particulate Filter, and a Variable Geometry Turbocharger that also runs the factory exhaust brake. A working fluid-dosing system continuously reports wrong fluid, component failure, or tampering, and an unserviced fault limits the truck to a maximum speed of 5 mph. Clean Air Act tampering prohibitions apply for the entire life of the vehicle, and an off-road or competition label does not create an exemption. Civil penalties reach a maximum of $5,911 per vehicle for an individual and $59,114 for a manufacturer or dealer. Updated 2026-08-16 ⚠️ Off-road / competition use only These products are sold for closed-course competition and off-road-only equipment. They are not intended or sold for use on vehicles registered for highway use. Modifying factory emissions equipment may void your powertrain warranty. Thanks for reading! As always, if you have any questions feel free to shoot us a message! The Diesel Dudes Technical Team Canonical: https://thedieseldudes.com/blogs/news/deleted-6-7-cummins