2026 Ram 3500 Fuel Filter Location: Both Filters Are on the Engine

# 2026 Ram 3500 Fuel Filter Location: Both Filters Are on the Engine Both of them are on the engine, side by side, on the driver side. If you have been under the truck looking for the second one, that is why you have not found it. This is worth stating plainly, because the layout is not the one most Cummins fuel filter advice describes. Everything below comes from Ram's own 2026 owner documentation for the 2500/3500 Heavy Duty trucks, and from Cummins' own engine documentation where the engine maker publishes a figure directly. ## Both filters are on the engine The 2026 owner's manual gives the count and the location in a single sentence: There are two engine mounted fuel filter assemblies mounted side-by-side on the driver side of the engine.oem-36 Two assemblies, one area of the truck. Neither is mounted under the body, and no part of finding them involves a lift or a set of ramps. Access follows from where they sit: The best access to the water drain valves is from under the hood.oem-36 So the whole job, both filters and both drain valves, happens from the engine bay. ## Front and rear, not upper and lower Because the two sit alongside each other, "front" and "rear" describe positions along the engine rather than positions along the truck. The manual labels them by their drain valves: Engine Mounted Fuel Filter Assembly 1 — Front Filter Drain Valve 2 — Rear Filter Drain Valveoem-36 Hold onto that naming, because the filter specifications are written against it. A specification addressed to the "front mounted filter" means the forward one of the two on the engine, not something ahead of the cab. ## How this differs from the older layout Most of the confusion about this truck comes from advice written for the previous arrangement, which put one filter somewhere you cannot see from above. On a 2024 Ram 2500 the second filter is not on the engine at all. The second one is on the under body, located in front of the rear axle above the drive shaft.oem-37 And it is serviced from below rather than from the engine bay: The best access to this water drain valve is from under the vehicle.oem-37 That single difference accounts for most of the bad directions you will find. On the older chassis, half this job happened on your back. On a 2026 none of it does. ## The two positions do not take the same filter This is where a side-by-side layout can cost you an injection system, because two filters within arm's reach of each other are easy to fit the wrong way round. The 2026 handbook names the part line first: We recommend using Mopar® Fuel Filters. Then it specifies the positions separately. The forward one is the tighter of the pair: Must meet 3 micron rating (front mounted filter).oem-35, oem-36 The other one is specified differently: Must meet 5 micron rating (rear engine mounted filter).oem-35, oem-36 Three micron in one position and five in the other is a real difference in what reaches the injectors, and the manual states what ignoring it costs: Using fuel filters that do not meet the manufacturer's filtration and water separating requirements can severely impact fuel system life and reliability.oem-36, oem-35, oem-37 Filtration is only half of what these assemblies do. Water separation is the other half, and on a diesel it is the half that decides how long the high-pressure side lasts. ## Water separation is the second job The manual is explicit that the water-handling side of these assemblies is engineered rather than incidental: Your Mopar®/Cummins® filtration system is designed to provide adequate fuel water separation capabilities.oem-36, oem-37 That capability is why the filter specification is not a formality. If you run any biodiesel blend, the manual attaches a parts requirement to both positions by name: You must use Mopar®/Cummins® approved fuel filter elements in both your engine mounted filter assemblies.oem-36, oem-37 There is a reason it says that in the biodiesel section specifically. Biodiesel fuel has a natural affinity to water and water accelerates microbial growth.oem-36, oem-37 So water in the tank is not only a corrosion and lubricity problem on these trucks; on a blend it is also a growth medium. The separator side of the filter assemblies is what stands between that and your injectors. ## Servicing them Both filters come out on the same schedule, and the schedule treats them as one job rather than two. Cummins states the interval on its own engine documentation without qualification: Maintenance intervals for fuel filter replacement remains at 15,000 miles (24,000 km).oem-10 Ram's 2026 maintenance plan puts the same job in the same group as the engine oil change, at Every 15,000 Miles (24,000 Km) — so in practice the filters and the oil come out on the same visit. That oil interval is written as a hard ceiling rather than a suggestion, which matters if you are the kind of owner who stretches services: Under no circumstances should oil change intervals exceed 15,000 miles (24,000 km) or 12 months or 500 Hours, whichever comes first.oem-07, oem-35, oem-36 ## Before you start: one caution about the engine bay Since the whole job now happens under the hood, one line from the same section of the manual is worth reading first. Cleaning the engine compartment with a high pressure washer is not recommended.oem-36, oem-37 The manual gives the reason, and it is about the connectors rather than the paint: Precautions have been taken to safeguard all parts and connections however, the pressure generated by these machines is such that complete protection against water ingress cannot be guaranteed.oem-36, oem-37 On a system whose entire purpose is keeping water out of the fuel, forcing water at the housings is a poor way to prepare for a filter change. ## Draining the water The drain is a separate job from the filter change, and it is time-bound in a way that catches people out. Start with the prohibition, because it is the one most often broken: Do not drain the fuel/water separator filter when the engine is running.oem-36, oem-37 The trigger is the dash light: Drain the fuel/water separator filters when the Water In Fuel Indicator Light is ON.oem-36, oem-37 Then the clock. Within 10 minutes of vehicle shutdown, turn the engine mounted filter drain valves (located on the side of the filter assembly) counterclockwise 1/4 turn.oem-36, oem-37 That ten-minute window is not arbitrary — it is the state the manual expects the system to be in when the valves open. After that the ignition goes to ON and the water is allowed to run out until what emerges is fuel rather than water. Closing the drain has its own specification, and this is the step where an expensive mistake is easy. First, rotate the 1/4 turn drain valves fully clockwise to their stops.oem-36 Then, and only by this much: Continue turning the drain 1/2 of a turn to properly compress the seal.oem-36, oem-37 Stop there. Over-compression of the seal due to over- tightening of the drain will damage the seal, cause a leak, and require the entire sensor to be replaced.oem-36, oem-37 That is why a manual bothers to specify a fraction of a turn on a drain valve. The seal being compressed belongs to the sensor assembly, so crushing it converts a five-minute drain into a parts order. The fluid that comes out is not ordinary waste, either: Care should be taken in disposing of used fluids from your vehicle.oem-36, oem-37 ## The water-in-fuel light is telling you one of two things There is a detail in the 2026 manual that turns this light from a single warning into a usable diagnostic, and it is the chime. When the system finds water while the engine is running, the light arrives with a count: an audible chime will be heard five times.oem-36, oem-37 A single chime is a different message entirely: If the Water In Fuel Indicator Light comes on and a single chime is heard while you are driving, or with the ignition switch in the ON position, there may be a problem with your water separator wiring or sensor.oem-36, oem-37 So count the chimes before deciding what you are dealing with. Five of them means the separator has caught water and the filters want draining; one means the truck is reporting a fault in the circuit that detects water, which draining will not fix. If the light is already on when you go to start, the manual does not hedge: If the Water In Fuel Indicator Light remains on, DO NOT START the engine before you drain water from the fuel filters to avoid engine damage.oem-36, oem-37 The light also lags the fix, which is the detail that makes owners think a good drain failed. Upon proper draining of the water from both fuel filters, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.oem-36, oem-37 And if the drain was done in the way the manual warns against, the lag is far longer. If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.oem-36, oem-37 Ten seconds is a normal delay. Three minutes means the drain happened with the engine running. ## Changing the filters The procedure has two steps in it that run directly against habits picked up on other engines. The first is priming, and it is stated as a caution: Do not prefill the fuel filter when installing a new fuel filter.oem-36, oem-37 The reason is contamination rather than convenience: There is a possibility debris could be introduced into the fuel filter during this action.oem-36, oem-37 And the correct method is the one that feels wrong: It is best to install the filter dry and allow the in-tank lift pump to prime the fuel system.oem-36, oem-37 The cartridge is protected in the same spirit. Do not remove cartridge from bag until you reach this step in order to keep cartridge clean.oem-36, oem-37 The sealing surfaces get attention before anything new goes in: Wipe clean the sealing surfaces of the lid and housing.oem-36, oem-37 The o-ring is a fitted part, not a dry one: Install new o-ring back into ring groove on the filter housing and lubricate with clean engine oil.oem-36, oem-37 Then the cartridge is seated deliberately: Push down on the cartridge to ensure it is properly seated.oem-36, oem-37 The second habit-breaker is the lid. Install lid onto housing and tighten to 22.5 ft-lb,oem-36, oem-37 which is a specification rather than a feel. And because there are two assemblies rather than one, the sequence runs twice: Repeat steps 5 through 11 for the second engineoem-36 ## Getting it running again Both filters are dry when you close them up, so the restart is a procedure rather than a turn of the key. It starts at the tank: Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).oem-36, oem-37 Then the lift pump does the priming, in cycles: Turn the ignition switch to the off position, and leave off for at least 30 seconds.oem-36, oem-37 When it fires, let it settle before you touch anything: Once the engine starts, allow the engine to idle for a minimum of 30 seconds.oem-36, oem-37 A rough idle at this point is expected rather than alarming. The engine may run rough until the air is forced from all the fuel lines.oem-36, oem-37 There is a hard limit on how long you may crank, and it protects the starter: Do not engage the starter motor for more than 15 seconds at a time.oem-36, oem-37 One warning outranks all of the above, and it is about pressure rather than fuel loss: Do not open the high pressure fuel system with the engine running.oem-36, oem-37 The reason is stated in the same caution: High pressure fuel spray can cause serious injury. ## Cold weather One more part of the assembly answers a question owners usually ask separately, which is why these trucks start in real winter: A 12 Volt heater built into the fuel filter housings aid in preventing fuel gelling.oem-36, oem-37 Gelling is diesel's cold-weather failure mode, and heated housings are a designed defence against it rather than an accessory somebody added later. The manual is careful about what it does and does not ask you to add. In addition, commercially available fuel additives are not necessary for the proper operation of your Cummins® diesel engine.oem-36, oem-37 There is one stated exception, with a temperature attached: However, if seasonably adjusted fuel is not available and you are operating below 20°F (-6°C), Mopar® Premium Diesel Fuel Treatment (or equivalent) may be beneficial to avoid fuel gelling.oem-36, oem-37 And a colder threshold changes the fuel itself rather than the additive: Number 1 Ultra Low Sulfur Diesel Fuel should only be used where extended arctic conditions (0°F or -18°C) exist.oem-36, oem-37 ## The short version Two filters, both on the engine, side by side on the driver side, both reached from under the hood. The forward one is the three micron filter and the rear one is the five micron filter, so they are not interchangeable. Both are replaced together at 15,000 miles, on the same visit as the oil. The new filter goes in dry, the lid is torqued, and the drain valve is closed to a specification rather than to feel. And if the water-in-fuel light appears, the number of chimes tells you whether you are draining water or chasing a sensor. ## Sources 1. 2026 Ram 2500/3500 Owner's Manual — Mopar vehicle information (Stellantis North America) 2. 2026 Ram 2500/3500 Owner's Handbook, maintenance schedule — Mopar vehicle information (Stellantis North America) 3. 2024 Ram 2500 Owner's Manual — Mopar vehicle information (Stellantis North America) 4. Cummins Inc., 6.7L Cummins engine information, 2019 Chassis Cab